技术文献

超声波传感器UC2000-30GM-E6R2-V15

阅读次数：2753 发布时间：2018/5/16 11:59:03

超声波传感器UC2000-30GM-E6R2-V15可用于灰尘，雾或蒸汽的场合，是进行非接触式的位置和距离测量的理想产品。在不考虑颜色或形状的情况下，不同材料的物体可以通过毫米级的精度被检测出。
超声波传感器采用超出人可听声之外的高频率超声波作为测量介质。通过传感器和物体间声波的传送时间就可计算出距离或位置。由于超声波传感器的可靠性和性，广泛用于木材，家具工业，建筑材料和设备，农业设备和液位控制场合。

技术数据：
产品尺寸：M30x1.5

一般说明检测范围80 ... 2000 mm调节范围120 ... 2000 mm盲区

0 ... 80 mm
标准目标板100 mm x 100 mm换能器频率约180 kHz响应延时
*小65 ms
出厂设定195 ms
工作方式/显示方式LED 绿色常亮：通电
闪烁：待机模式或设定状态下检测到目标物LED 黄色1常亮：开关状态开关输出1 闪烁：设定功能
LED 黄色2常亮：开关状态开关输出2 闪烁：设定功能
LED 红色常亮：温度/设定插头未连接
闪烁：出错或设定状态下未检测到目标物温度/设定插头温度补偿，开关点设定，输出功能设定电气参数工作电压10 ... 30 V DC,纹波10 %PP空载电流I0≤ 50 mA
接口接口类型RS 232, 9600 Bit/s,无奇偶校验, 8数据位, 1停止位输入/输出同步
双向
0-level: -UB ... +1 V1-level: +4 V ... +UB输入阻抗: > 12 kΩ
同步脉冲: ≥ 100 μs,同步脉冲周期: ≥ 2 ms同步频率
一般操作模式≤ 30 Hz
多重操作模式≤ 30/n Hz, n =传感器数量
输出输出类型2个开关量输出pnp,¨NO/NC可选重复精度
≤ 0.1 %满量程值
额定工作电流Ie
200 mA,短路保护/过载保护电压降Ud≤ 2.5 V开关频率f≤ 2.5 Hz
迟滞范围 H 可调整开关距离的1 %（缺省设置），可调温度漂移≤满量程值的2 %（带温度补偿）≤ 0.2 %/K（不带温度补偿）符合标准标准IEC / EN 60947-5-2周围环境环境温度-25 ... 70 ºC (248 ... 343 K)储存温度-40 ... 85 ºC (233 ... 358 K)机械特性防护等级IP65
连接方式V15连接器( M12 x 1), 5针
材料外壳不锈钢 1.4303塑料部分PBT
英文参数表（English parameter list）：

General specifications
Sensing range		80 ... 2000 mm
Adjustment range		120 ... 2000 mm
Dead band		0 ... 80 mm
Standard target plate		100 mm x 100 mm
Transducer frequency		approx. 180 kHz
Response delay		65 ms minimum 195 ms factory setting
Indicators/operating means
LED green		solid: Power-on flashing: Standby mode or program function object detected
LED yellow 1		solid: switching state switch output 1 flashing: program function
LED yellow 2		solid: switching state switch output 2 flashing: program function
LED red		solid: temperature/program plug not connected flashing: fault or program function object not detected
Temperature/TEACH-IN connector		Temperature compensation , Switch points programming , output function setting
Electrical specifications
Operating voltage		10 ... 30 V DC , ripple 10 %SS
No-load supply current		≤ 50 mA
Interface
Interface type		RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit
Input/Output
Synchronization		bi-directional 0 level -UB...+1 V 1 level: +4 V...+UB input impedance: > 12 KOhm synchronization pulse: ≥ 100 µs, synchronization interpulse period: ≥ 2 ms
Synchronization frequency
	Common mode operation	max. 30 Hz
	Multiplex operation	≤ 30 Hz / n , n = number of sensors , n ≤ 5
Output
Output type		2 switch outputs PNP, NO/NC, programmable
Rated operating current		200 mA , short-circuit/overload protected
Voltage drop		≤ 2.5 V
Repeat accuracy		≤ 0.1 % of full-scale value
Switching frequency		≤ 2.5 Hz
Range hysteresis		1 % of the adjusted operating range (default settings), programmable
Temperature influence		≤ 2 % from full-scale value (with temperature compensation) ≤ 0.2 %/K (without temperature compensation)
Approvals ａnd certificates
EAC conformity		TR CU 020/2011
UL approval		cULus Listed, General Purpose
CSA approval		cCSAus Listed, General Purpose
CCC approval		CCC approval / marking not required for products rated ≤36 V
Ambient conditions
Ambient temperature		-25 ... 70 °C (-13 ... 158 °F)
Storage temperature		-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type		Connector M12 x 1 , 5-pin
Degree of protection		IP65
Material
	Housing	stainless steel (1.4305 / AISI 303) PBT plastic parts
	Transducer	epoxy resin/hollow glass sphere mixture; polyurethane foam
Mass		140 g